The Load Bearing CompanyStructural & steel works0161 706 3593Free survey
Guide · Updated 7 November 2026

Chimney breast removed without building regs: what to check, and how to put it right before you buy or sell

The short answerFirst find out what is holding up the chimney above. If the breast came out but the stack stayed, it needs proper support, ideally a steel beam designed by a structural engineer. Then put the paperwork right: check the council's building control records, and if there's no completion certificate, apply to the council to regularise the work.

Why it comes up

Chimney breasts have been taken out of houses for decades, often long before anyone thought to involve building control. A breast came out of a front room or a kitchen to gain space, and the chimney above was left where it was. Some were carried on steel gallows brackets, some on a timber or concrete lintel, and some on nothing more than the wall they were built into.

It usually comes to light when the house is sold. The buyer's surveyor sees a chimney stack in the loft or on the roof with no breast below it and recommends a structural engineer's inspection. The buyer's solicitor asks for the Building Regulations completion certificate. If there isn't one, the sale stalls until someone deals with it.

Step one: find out what is holding the chimney up

Work out how much of the chimney has gone. If the breast and the stack were both taken out all the way through the roof, there may be nothing left above to carry, and the question is mostly paperwork. If any of the chimney remains above the removed section, in a bedroom or in the loft, it is sitting on something, and that something is what matters.

The base of the remaining stack is often visible from the loft. Where the support is hidden in a ceiling, an engineer will open up a small section to see it. What you find is usually one of these:

  • A steel beam under the remaining chimney, bearing on padstones in the walls either side: the modern approach, and the one building control expects to see backed by an engineer's calculations
  • Steel gallows brackets: angled brackets fixed to the wall under each side of the stack. Once common, but most building control bodies now expect engineer's calculations for any support, so brackets on their own are often not accepted
  • A timber or concrete lintel, or a length of steel resting on the floor joists: not designed for the load, and a common cause of cracking
  • Nothing visible at all, with the remaining brickwork held only by the wall it is bonded into. This is the one to get looked at quickly

Signs it needs attention now

Whatever the paperwork says, these are reasons not to wait for a sale:

  • Cracks in the ceiling or wall directly under where the stack sits
  • A ceiling that has dropped or bowed beneath it
  • Diagonal cracks in the wall the chimney is built into, on your side or your neighbour's
  • Brickwork in the loft that has moved, with open joints or mortar on the floor below it
  • Damp or soot staining where the old flue was left open

What to do if you see those signs

Get a structural engineer to look, and have the chimney propped if they say so. Propping is quick and temporary, and it takes the risk away while the permanent support is designed and approved. Don't load the floor or the loft around the stack in the meantime.

Step two: the paperwork

Start by checking whether the work was approved after all. The council's building control department holds records of applications and completion certificates, and many will confirm by email or phone if you give them the address. Work done through a private approved inspector is also registered with the council. If a certificate exists, ask for a copy and the problem may already be solved.

If there is no record, there are two routes, and they are not equal:

  • Regularisation: an application to the council for work done without approval. In England and Wales it applies to work carried out since 11 November 1985. Building control inspect, usually ask for some of the work to be opened up and for an engineer's calculations for the support, and require anything that doesn't comply to be put right. At the end they issue a regularisation certificate, which does the job of a completion certificate on a sale. Regularisation is only available from the council, not from a private approved inspector
  • Indemnity insurance: a one-off policy that covers the cost if the council later takes enforcement action over the missing approval. It is quick and solicitors often suggest it, but it does nothing to make the chimney safer, and it is normally void if anyone has already contacted the council about the work

Which route to take

If the support is sound and properly sized, either route can close the sale, though only regularisation actually answers the question of whether the work is safe. If the support is makeshift or missing, insurance is papering over a structural problem: a buyer who knows the chimney is unsupported won't be reassured by a policy, and the next survey will ask the same question again. Fix the structure, then regularise it.

Step three: putting the support right

The fix is the same work as a chimney breast removal done properly, picking up from the point where the breast is already gone:

  • A structural engineer inspects, measures the remaining chimney and designs the support: usually a steel beam on padstones
  • A party wall notice to the neighbour where the chimney sits on the party wall, which in semis and terraces it usually does. Their flue must stay intact
  • The remaining stack is propped, the old brackets or makeshift support come out, and the new steel goes in and is packed tight to the masonry above
  • Building control inspect the steel and the bearings before it is boxed in, then the beam is fire protected and the ceiling and wall made good
  • The flue is capped and vented if it was left open
  • Building control's sign-off at the end, through the regularisation application

Or take the rest of the chimney down

Where the breast has gone and the stack is still there, the alternative to supporting it is removing what remains, through the roof if nothing else uses it. That changes the outside of the house, so check with the council first if the property is listed or in a conservation area. On a shared stack it needs the neighbour's agreement, and their flue has to stay.

What it costs

Every chimney is different, so we price after seeing it. The parts of the bill are the same as for any domestic beam, and they are the figures in our published cost guide: a structural engineer's design typically £350–£1,000 for a domestic beam, the steel itself usually £200–£500 for a single domestic section, and £300–£1,000 for building control on a domestic job. Regularisation fees are set by the council, and putting work right afterwards costs more than having it approved first. Where the chimney sits on a party wall and the neighbour appoints a surveyor, allow £700–£1,000+ per appointed surveyor.

On top of that is the labour, propping and making good, which depends on how much ceiling and wall has to be opened up to get at the support.

If you're buying, or selling

Buying: ask the seller for the completion certificate or proof of approval. If there isn't one, get an engineer to look at the support before you exchange, then either agree that the seller puts it right and regularises it, or get a price for the work and agree a reduction. Tell your lender, because some will want it resolved before the mortgage completes.

Selling: if you know about it, deal with it before the house goes on the market. A chimney that has been checked, supported on steel and regularised stops being a question in the buyer's survey. Leaving it until a buyer's surveyor finds it usually means doing the same work against a deadline.

Related questions

Is a chimney breast removed without building regs illegal?

Structural work without approval contravenes the Building Regulations, and the council can require it to be put right. In practice the bigger problems are the missing certificate stalling a sale, and the chimney itself if it isn't properly supported. Regularisation brings it back into line.

Are gallows brackets acceptable?

Sometimes, but don't assume so. Gallows brackets were once a standard way to carry a chimney after the breast came out. Most building control bodies now expect engineer's calculations for any support, and on an old job with no paperwork they will usually want the brackets checked or replaced with a steel beam.

Can I just get indemnity insurance instead?

You can, and it covers the cost of council enforcement over the missing approval. It does nothing for the structure, and it is normally void if the council has already been contacted. If there's any doubt about the support, have it checked first.

Who should I call first, an engineer or building control?

If there are cracks or signs of movement, an engineer first, so the chimney can be propped and the support designed. If it all looks sound, check the council's building control records first: a certificate may already exist.

Ready to take it further? See our chimney breast removal service.

Read next

Want a straight answer about your project?

Send photos and rough sizes — we'll tell you honestly what it needs, what it doesn't, and what it should cost.