The Load Bearing CompanyStructural & steel works0161 706 3593Free survey
Guide · Updated 16 November 2026

Do I need a structural engineer to remove a wall?

The short answerFor a load-bearing wall, yes in practice. Building control have to be satisfied the new beam meets Part A of the Building Regulations, and for a steel beam that means a structural engineer's calculations. For a wall that is genuinely not load-bearing you usually don't need one, but someone competent should confirm that first.

Why can't the builder just pick a beam?

Because the law asks for a structure that safely carries its loads, and someone has to show it does. Requirement A1 in Schedule 1 to the Building Regulations 2010 says a building must carry its dead, imposed and wind loads to the ground safely, without deflection or movement that harms the building or a neighbour's.

Removing a load-bearing wall is a material alteration under regulation 3, because it affects Part A. The beam size, its bearings and its connections are what demonstrate compliance, and building control will ask for the calculations.

Does building control always ask for calculations?

For a steel beam, expect to provide them. Even on a building notice, where no plans are approved in advance, Manchester City Council says it may ask for plans and calculations at a later stage. Most inspectors want to see them before the beam is covered up, so the inspection can check the steel on site matches the design.

What does the engineer actually do?

A visit to the house, then a design. The work usually covers:

  • Tracing what the wall carries: floor joists, walls above, roof struts, a chimney or a water tank
  • Sizing the beam for the span and the load, including how much it can safely bend
  • Checking what the beam sits on, and sizing padstones or posts so the masonry is not overloaded
  • Detailing connections where one beam carries another, and any posts down to new foundations
  • Setting out the information building control and any party wall surveyor will want to see

What is in the calculation pack?

Usually a short report with the loads, the beam and padstone sizes, and a sketch or drawing showing where everything goes. It names the steel section, so the supplier can cut it and the inspector can check it on site.

Keep it with the completion certificate. Your buyer's surveyor or solicitor may ask for both when you sell.

When might you not need one?

When the wall carries nothing but itself: a stud partition with the joists running parallel to it, and nothing above resting on it. Even then, confirm it first. Walls that look like partitions can carry ceiling joists or roof struts, especially upstairs and in older houses.

A new opening in a structural wall should still be designed, however small it is.

How long does the design take?

Allow a site visit and then a short wait for the calculations, which varies with how busy the engineer is. It is usually quicker than the party wall notice period, which is at least two months where notice is needed. Getting the engineer in first means the notice, the building control application and the steel order can all follow from one set of drawings.

What does it cost?

Typically £350–£1,000 for a domestic beam, and into the thousands on commercial or complex jobs. It is a small part of a typical £1,800–£4,500 wall removal, and the one that stops the beam being too small or needlessly heavy.

We arrange the engineer as part of the job, so the design is done with the installation in mind.

Related questions

Can I use an engineer's design from my neighbour's identical house?

Not safely. Houses that look the same can have different joist directions, roof framing or wall construction. The calculations are for a specific wall in a specific house, and building control expect them to match what is on site.

Does the engineer need to visit, or can it be done from photos?

A visit is best. The engineer needs to see which way the joists run, what is in the loft and what the wall is built of. Remote designs miss things that only show up on site.

Does the engineer inspect the work?

Not always. Building control carry out the statutory inspections. Some engineers also visit to check bearings or answer questions on site, which is worth having on complex jobs.

Ready to take it further? See our load-bearing wall removal service.

Read next

Want a straight answer about your project?

Send photos and rough sizes — we'll tell you honestly what it needs, what it doesn't, and what it should cost.