Can you remove a load-bearing wall upstairs? First-floor walls, roof loads and what changes
What does an upstairs wall usually carry?
A first-floor wall can be carrying the ceiling joists, any boarded loft floor, and parts of the roof through struts or binders that land on it. In older houses the roof is often propped off internal walls in this way. Modern trussed roofs usually span between the outside walls, but some trusses still bear on internal stud walls.
Look in the loft above the wall. Timbers resting on it or struts running down to it are a strong sign it is doing a job. Only an engineer's inspection confirms it.
Where does the new beam go?
There are two usual places. The beam can sit in the ceiling, either below the joists as a boxed-in downstand or up between them so the ceiling stays flat. Or it can sit in the loft above the ceiling joists, with the joists hung from it, which keeps the bedroom ceiling flat without cutting into it.
The loft route depends on headroom and access. The engineer picks the option that suits the load and the room.
What holds up the ends of the beam?
This is the part that makes upstairs walls different. The beam's load has to reach the ground, and the wall below each end is not always in the right place. The engineer checks every bearing all the way down.
- Ends on walls that continue to the ground floor: the simplest case, using padstones
- Ends landing over a ground-floor opening: the beam or lintel below must be checked for the new load
- Ends landing on a timber floor with nothing beneath: usually a steel post down through the floor to a new pad foundation
- Ends bearing into a party wall: a party wall notice to the neighbour before work starts
How is it propped?
Props go under the ceiling and roof timbers upstairs, but a first-floor timber floor may not take their load on its own. Props are often carried on through to the ground floor beneath, so the weight goes straight down to something solid. It means two rooms are disturbed, not one, so plan for that.
Does it need building regulations approval?
Yes, if the wall is load-bearing. Regulation 3 of the Building Regulations 2010 treats an alteration as material if it could leave the building failing a relevant requirement, and the list covers Part A (structure) and paragraph B1 (means of warning and escape).
B1 matters upstairs. Opening a bedroom onto the landing or stairs can change how you escape in a fire, especially in a house with a loft conversion, so building control will look at the escape route as well as the steel.
Does the beam need fire protection?
Usually. Steel in homes normally has to be protected to satisfy building control, typically by boxing it in fire-rated plasterboard or using intumescent paint. A beam hidden in the loft or in the ceiling is often protected by the plasterboard around it, but the engineer and building control confirm what is needed.
How do you get a steel beam upstairs?
Up the stairs where it fits, or in through a window. A long steel does not always make the turn on a landing, so where access is tight the engineer can design a beam made in sections and bolted together in place.
What does it cost?
We price after seeing the wall, because upstairs walls add propping complexity and the bearings can need posts or foundations. Our published figures for any domestic wall are the starting point: £1,800–£4,500 including the steel beam and installation for a typical opening, plus £350–£1,000 for the engineer's calculations and £300–£1,000 for building control.
Related questions
Can I take out a stud wall upstairs without building regs?
Only if it is genuinely non-load-bearing and removing it does not affect the fire escape route. Upstairs stud walls often carry ceiling joists or roof struts, so get it checked before you start.
Will removing an upstairs wall affect the roof?
It can, if roof struts or binders land on the wall. That is why the engineer traces the roof load before designing the beam. Done properly, the roof is carried by the new steel and nothing moves.
Can two bedrooms be knocked into one?
Usually, yes. It is a common way to make a larger main bedroom. The wall between them is often load-bearing, so it needs a beam, calculations and approval like any other structural wall.
Ready to take it further? See our load-bearing wall removal service.