The Load Bearing CompanyStructural & steel works0161 706 3593Free survey
Guide · Updated 16 November 2026

Removing a load-bearing wall in a bungalow: the roof, the ceiling and where the beam goes

The short answerIn a bungalow, internal walls often carry the ceiling joists and, in older roofs, struts holding up the purlins, so many are load-bearing even with nothing upstairs. With a modern trussed roof, internal walls may carry little. Check from the loft first. If the wall is structural, an engineer designs a beam, sometimes hidden above the ceiling.

If there is nothing upstairs, what does the wall carry?

The roof and the ceiling. In a bungalow with a traditional cut roof, the rafters rest on purlins, and the purlins are often propped on struts down to an internal wall. The ceiling joists may also rest on the same wall to halve their span.

Take the wall out and that load has nowhere to go. That is why bungalow walls catch people out.

How do I check from the loft?

With care and a good torch, standing on the joists or boards. Look along the line of the wall below for:

  • Timber struts running from the roof down to a beam or plate over the wall
  • Ceiling joists ending or overlapping on top of the wall
  • A water tank or other heavy load standing over it
  • Trussed rafters, triangulated frames with metal plates at the joints, which usually span between the outside walls

Does a trussed roof mean the wall can come out freely?

Not necessarily. Trusses are designed to span between the outside walls, so internal walls under them often carry no roof load. But ceiling joists, binders or a tank platform can still bear on a wall, and some trussed roofs have girder trusses with their own support. An engineer should confirm before anything is removed.

Can the beam go in the loft instead of below the ceiling?

Often, yes, and it is one of the advantages of a bungalow. Instead of a downstand under the ceiling, the beam sits in the loft above the ceiling joists, which are hung from it. The struts are picked up on the beam, and the room below gets a flat ceiling with no bulkhead.

The beam still needs proper bearings at each end, usually padstones on the walls it lands on.

Does it need building regulations approval?

Yes, if the wall is load-bearing. Removing it is a material alteration under regulation 3 of the Building Regulations 2010 because it affects Part A (structure). Building control will want the engineer's calculations and to see the beam and its bearings before they are covered.

Working in the loft also means thinking about insulation and access, which the installer makes good afterwards.

What if I'm planning a loft conversion later?

Say so before the beam is designed. A loft conversion changes the loads, often needs new floor joists and steels in the roof, and brings fire escape requirements. Designing the wall removal with the conversion in mind avoids paying for steel twice.

What does it cost?

A single opening sits within our published £1,800–£4,500 range for the steel and installation, plus £350–£1,000 for the engineer and £300–£1,000 for building control. Beams in the loft involve more work at height and on the roof timbers, so we price after seeing the loft.

Related questions

Is the wall under the ridge always load-bearing?

Not always, but in a cut roof it often is, because struts or a ridge support can land on it. In a trussed roof it may carry nothing from the roof. The loft tells you which.

Will the ceiling crack when the wall comes out?

It shouldn't, if the ceiling joists are supported and propped first. Small cracks along the line of the old wall are made good when the room is plastered.

Can I do the loft check myself?

You can look and take photos, which helps the engineer. Don't move or cut any roof timber, and leave the decision about what is load-bearing to a professional.

Ready to take it further? See our load-bearing wall removal service.

Read next

Want a straight answer about your project?

Send photos and rough sizes — we'll tell you honestly what it needs, what it doesn't, and what it should cost.